Jai CV-M530 User Manual

Operation ManualRemote Head Monochrome CCD Camera(Rev.E)CV-M530/531

- 9 -CV-M530/531CCIR (Non-interlaced / Field accumulation mode)Edge pre-select mode (for non-interlace only)CCIR : 1H = 64µsTRIGINT VDEENWENEXT HDINT

- 10 -CV-M530/531Cautions in the Pulse Width Control Mode.1. Pulse width control mode is effective only in non-interlaced field accumulation mode.2. T

- 11 -CV-M530/5316.3.3. Start/Stop Trigger ModeThe Start /Stop trigger will work in 3 modes:1. Interlaced with frame accumulation.2. Interlaced with f

- 12 -CV-M530/531Cautions in the Start/Stop Trigger Mode.1. The input of ext. VD signal must be given continuously to synchronize with int. VD signal.

- 13 -CV-M530/5316.3.4. Long Time Exposure ModeThe Long time exposure will work in 3 modes:1. Interlaced with field accumulation.2. Interlaced with fr

- 14 -CV-M530/531Cautions in the Long Time Exposure Mode.1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞. CCIR: 1/25 sec. to ∞ .2. It

- 15 -CV-M530/5317. Mode SettingCaution on Mode Setting.Before making any mode or jumper setting turn the power OFF.7.1.1. SW1 Switch on the Rear Pane

- 16 -CV-M530/5317.1.4. Ext. Trigger Shutter ModeWhen trigger select SW1-4 is ON. The camera is in ext. trigger shutter mode. The SW1-1, SW1-2 and SW1

- 17 -CV-M530/5317.3. Jumper SettingsCaution on Jumper Setting.Before making any mode or jumper setting turn the power OFF.Jumpers for mode setting ar

- 18 -CV-M530/5317.4. Location of SW2 and JumpersJumpers are shorted with a 0 Ohm resistor or by a soldering between the 2 points. To remove the solde

CV-M530/531DECLARATION OF CONFORMITYAS DEFINED BY THE COUNCIL DIRECTIVE89/336/EECEMC (ELECTROMAGNETIC COMPATIBILITY)WE HEREWITH DECLARE THAT THIS PROD

- 19 -CV-M530/5318. Adjustment of Video Signal Output LevelWhen an alignment of a video output signal is required, remove the camera housing and adjus

- 20 -CV-M530/5319. External AppearanceUnit : mm (inches)9.1 CCU9.2 HEAD

- 21 -CV-M530/53110. SpecificationsScanning system CCIR 625 lines EIA 525 lines25 frames/sec. 30 frames/sec.CCD sensor Monochrome 1/2" Hyper HAD

- 22 -CV-M530/53111. Appendix11.1. PrecautionsPersonnel not trained in dealing with similar electronic devices should not service this camera.The came

JAI America, Inc., USASuite 45023046 Avenida de la CarlotaLaguna Hills, CA 92653USAPhone +1 949 472 5900Fax +1 949 472 5908www.jai.comJAI Corporation,

- 2 -CV-M530/531Table of ContentsTable of Contents ...

- 3 -CV-M530/5311. GeneralThe model CV-M530/531 are new remote head (ø28mm) camera systems, designed to accept standardC-mount lens, and have virtuall

- 4 -CV-M530/5313. Main Features• Remote head - ø28mm (1.10 inches) separated from camera control unit via a 0.5m or 2.0m cable.• 1/2" Hyper HAD

- 5 -CV-M530/5314. Locations and Functions4-1. CCU4-2. HEAD1 12P connector : To connect camera head with camera control unit(For Camera Head)2 Video

- 6 -CV-M530/5315. Pin Assignment5.1. 12-pin Multi-connector (DC-IN/SYNC.)Type: HR10A-10R-12PB (Hirose) maleSeen from rear.Notes:*1) Signals on pin no

- 7 -CV-M530/5316. Functions and Operations6.1. Input/Output of HD/VD Signal6.1.1. Input of External HD/VD SignalAs factory setting the camera can be

- 8 -CV-M530/531To use this modeSet: SW1-4 to ON for ext. trigger shutterSW1-5 to OFF for field accumulationSW1-6 to ON for non-interlacedSW1-1,2 and