Operation ManualIndustrial Monochrome CCD Camera(Rev.E)CV-M300
- 9 -CV-M300Cautions in the Pulse Width Control Mode.1. Pulse width control mode is effective only in non-interlaced field accumulation mode.2. The ex
- 10 -CV-M3006.3.3. Start/Stop Trigger ModeThe Start /Stop trigger will work in 3 modes:1. Interlaced with frame accumulation.2. Interlaced with field
- 11 -CV-M300Cautions in the Start/Stop Trigger Mode.1. The input of ext. VD signal must be given continuously to synchronize with int. VD signal. It
- 12 -CV-M3006.3.4. Long Time Exposure ModeThe Long time exposure will work in 3 modes:1. Interlaced with field accumulation.2. Interlaced with frame
- 13 -CV-M300Cautions in the Long Time Exposure Mode.1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞. CCIR: 1/25 sec. to ∞.2. It is re
- 14 -CV-M3007. Mode SettingCautions on Mode Setting.Before making any mode or jumper setting turn the power OFF.7.1.1. SW1 Switch on the Rear PanelFa
- 15 -CV-M300Cautions on Shutter.The image can flicker when the illumination is AC powered.Highlighted parts of the image will show increasing smear a
- 16 -CV-M3007.3. Jumper SettingsCautions on Jumper Setting.Before making any mode or jumper setting turn the power OFF.Jumpers for mode setting are f
- 17 -CV-M3007.4. Location of SW2 and JumpersJumpers are shorted with a 0 Ohm resistor or by a soldering between the 2 points. To remove the soldertin
- 18 -CV-M3008. Adjustment of Video Signal Output LevelWhen an alignment of a video output signal is required, remove the camera housing and adjustpot
CV-M300DECLARATION OF CONFORMITYAS DEFINED BY THE COUNCIL DIRECTIVE89/336/EECEMC (ELECTROMAGNETIC COMPATIBILITY)WE HEREWITH DECLARE THAT THIS PRODUCTC
- 19 -CV-M3009. External AppearanceUnit : mm (inches)Tripod mount plate
- 20 -CV-M30010. SpecificationsScanning system CCIR 625 lines EIA 525 lines25 frames/sec. 30 frames/sec.CCD sensor Monochrome 2/3" IT CCDSensing
- 21 -CV-M30011. Appendix11.1. PrecautionsPersonnel not trained in dealing with similar electronic devices should not service this camera.The camera c
- 22 -CV-M30012. User’s RecordCamera type: CV-M300Scanning system: EIA/CCIRRevision: (Revision E)Serial No. ...Users Mode SettingsUsers
JAI America, Inc., USASuite 45023046 Avenida de la CarlotaLaguna Hills, CA 92653USAPhone +1 949 472 5900Fax +1 949 472 5908www.jai.comJAI Corporation,
- 2 -CV-M300Table of ContentsTable of Contents ...
- 3 -CV-M3001. GeneralThe CV-M300 is a monochrome 2/3" CCD camera designed for automated imaging applicationsfeaturing high performance and uniqu
- 4 -CV-M3004. Locations and Functions1 2/3" interline transfer CCD sensor.2 Lens mount of C-mount type. *1)3 BNC connector for video output.4 Sw
- 5 -CV-M3005. Pin Assignment5.1. 12-pin Multi-connector (DC-IN/SYNC.)Type: HR10A-10R-12PB-01 (Hirose) maleSeen from rear.Notes:*1) Signals on pin no.
- 6 -CV-M3006. Functions and Operations6.1. Input/Output of HD/VD Signal6.1.1. Input of External HD/VD SignalAs factory setting the camera can be sync
- 7 -CV-M300To use this modeSet: SW1-4 to ON for ext. trigger shutterSW1-5 to OFF for field accumulationSW1-6 to ON for non-interlacedSW1-1, 2 and 3 t
- 8 -CV-M300CCIR (Non-interlaced / Field accumulation mode)6.3.2. Pulse Width Control ModeThe pulse width control mode will only work in non-interlace
Comments to this Manuals